Triumph675.Net Forums - Search Results
Advanced Search
Showing results 1 to 13 of 13
Search took 0.01 seconds.
Search: Posts Made By: vincenzo
Forum: Electrical Section   04-28-15, 12:18
Replies: 38
Views: 11,550
Posted By vincenzo
I build all my hardware myself, so I don't know...

I build all my hardware myself, so I don't know about freematics.com ... anyway, all you need to connect to the dash is a CAN bus 'reader', any OBD-II device will do. The challenge is to get the...
Forum: Electrical Section   04-28-15, 12:12
Replies: 38
Views: 11,550
Posted By vincenzo
The way is not so magic (I have access to all the...

The way is not so magic (I have access to all the communication between the dash and the ECU), but I haven't had time/need to figured out what all is needed to run without the dash.

As soon as...
Forum: Electrical Section   02-17-15, 17:03
Replies: 38
Views: 11,550
Posted By vincenzo
http://onkickstand.com/daytona-hacking/img/tracker...

http://onkickstand.com/daytona-hacking/img/tracker-board-connectors.jpg

From left to right it's SMA for active GPS antenna, CAN Bus & 12V power, then Mini USB and SD Card right under it.
Forum: Electrical Section   02-03-15, 07:18
Replies: 38
Views: 11,550
Posted By vincenzo
See the photo on the first page of the thread. I...

See the photo on the first page of the thread. I made an extension cable that plugs in between the instrument panel and the ECU. It has the CAN bus wires & power wired out for my logging device...
Forum: Electrical Section   01-07-15, 18:19
Replies: 38
Views: 11,550
Posted By vincenzo
The instrument panel has information on which...

The instrument panel has information on which gear you are in, what speed you're doing, RPMs, ... I hope that's part of the CAN messages.
I would have to query the (slow) K-line OBD on the old...
Forum: Electrical Section   01-07-15, 15:40
Replies: 38
Views: 11,550
Posted By vincenzo
I took a break from the 2015 Daytona today and...

I took a break from the 2015 Daytona today and started playing with the "previous generation".

I attached the modified ECU <-> instrument panel connector, with a separate CAN bus connector, which...
Forum: Electrical Section   01-03-15, 07:16
Replies: 38
Views: 11,550
Posted By vincenzo
I happen to have a custom build hardware for the...

I happen to have a custom build hardware for the OBD, so I can tap the tx/rx lines between the bluetooth receiver and the STN1110 and see what's going on the same way as if it was a serial cable.
...
Forum: Electrical Section   01-03-15, 05:03
Replies: 38
Views: 11,550
Posted By vincenzo
Hi DKC, wow, looks like you're way ahead of me...

Hi DKC,
wow, looks like you're way ahead of me on this! Good job! :thumbsup:
As you suggested, one way to get the crypto key is to disassemble the Dealer Tool and check what it is doing in the...
Forum: Electrical Section   12-26-14, 09:00
Replies: 38
Views: 11,550
Posted By vincenzo
'takes some doing' ... ok, will check what...

'takes some doing' ... ok, will check what TuneECU does with the 2013 Daytona.

In the meantime, I did some analysis of the data on the CAN when the bike is powered up (engine off). The result is ...
Forum: Electrical Section   12-19-14, 07:10
Replies: 38
Views: 11,550
Posted By vincenzo
The harness for tapping the CAN bus connection...

The harness for tapping the CAN bus connection between the instrument panel and the ECU is ready. If there's time I'll try hooking it up today.
...
Forum: Electrical Section   12-17-14, 06:34
Replies: 38
Views: 11,550
Posted By vincenzo
That's exactly what I found as well ... the new...

That's exactly what I found as well ... the new Daytona seem to be ignoring all the standard OBD PIDs, even the ones that are supposed to just list supported PIDs. Either the delay is too long and...
Forum: Electrical Section   12-15-14, 16:40
Replies: 38
Views: 11,550
Posted By vincenzo
Yup, that much I know, as I mentioned ... but...

Yup, that much I know, as I mentioned ... but don't know how to interpret the data on the bus, thus my questions about that.


Yes, there are (Torque, Harry's Lap Timer, ..) and I'm already using...
Forum: Electrical Section   12-14-14, 15:08
Replies: 38
Views: 11,550
Posted By vincenzo
Daytona 675 CAN Bus Sniffing

I've read some posts on the topic of CAN Bus and Daytona 675 ... haven't really found any thread that would get to any sensible results, so I started from the scratch myself. The goal is to build a...
Showing results 1 to 13 of 13

 
Forum Jump
 
For the best viewing experience please update your browser to Google Chrome