Triumph675.Net Forums - Reply to Topic
General 675 discussion Anything related to the Triumph 675 model(s), and miscellaneous motorcycle talk.

Thread: Annitori RL quickshifter instructions Reply to Thread
Title:
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now



In order to be able to post messages on the Triumph675.Net Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
02-29-20 01:43
TTRIgnitionSystems *nods* US$250 (sensor & controller) => AU$385, but not such a deal if you wind up selling the bike.
02-29-20 00:37
bluedaytona02 Both bikes are gen 1 so need the stand alone units.

At this stage the "old" bike is being used as a wet bike, however the local track is being resurfaced (what a debacle) so I've not been able to test the new bike before it's first outing next week.
And as usual, life throws a few curve balls, and I'll likely need to sell the "wet" bike in the near future.

This QS unit comes with a blanking plug to allow you to unplug the sensor and still leave the coil loom in place. If symptoms persist, I'll just unplug it.

I'm not really in the market for another... and the AUD is pathetic when converted.

Sent from my SM-G960F using Tapatalk
02-29-20 00:24
TTRIgnitionSystems If the symptoms persist on the new bike, unplug the sensor. If the problems go away, it's the switch; if they remain, it's the controller (unlikely, but possible). Assuming IT doesn't have a bad CPS!


So ... Do you need a replacement QS for the original bike? Such a deal ...
02-29-20 00:09
bluedaytona02 I built another bike over the off season, so the QS is actually on that bike now. I guess it should then easily show if it's working properly or not.

Sent from my SM-G960F using Tapatalk
02-28-20 23:58
TTRIgnitionSystems Yup - agreed & conceded. Either a loose / broken QS switch with contacts flapping about inside, or a bad CPS breaking sync in the ECU.
02-28-20 23:18
bluedaytona02
Quote:
Originally Posted by TTRIgnitionSystems View Post
Harsh shifting sounds more like the cut time was way too long.
The engine would cut out like the QS switch was being activated, however my foot was not near the shifter and the sensitivity was on the lowest setting. It wasn't just occasionally either.

Sent from my SM-G960F using Tapatalk
02-28-20 21:32
TTRIgnitionSystems Harsh shifting sounds more like the cut time was way too long.
02-28-20 21:14
bluedaytona02
Quote:
Originally Posted by TTRIgnitionSystems View Post
I can't comment on setting sensitivity, but there should be no issue grounding to the main ground bus. The instruction to ground it to the battery is more likely for your own convenience, so you don't need to go hunting.
I was trying to eliminate a poor ground as a potential issue.

The bike was cutting out violently at WOT. It was suggested that the QS sensor was faulty. It was worse however the more fuel I added (But not sluggish like a fuel issue). So I removed the SQ and replaced the fuel pump internals. Next race meet the CPS failed, so I put the violent cut-out down to that.
I've now replaced the CPS and reinstalled the QS but am yet to test.

Sent from my SM-G960F using Tapatalk
02-28-20 18:40
TTRIgnitionSystems I can't comment on setting sensitivity, but there should be no issue grounding to the main ground bus. The instruction to ground it to the battery is more likely for your own convenience, so you don't need to go hunting.
02-28-20 16:03
bluedaytona02
Annitori RL quickshifter instructions

Does anyone have the instructions for the old Annitori RL quickshifter unit with the round control module?

I want to check/adjust sensitivity.

The Annitori site only has the Pro unit details.

I've also earthed it to the main earth rather than the battery. I had issues which presented like a failing QS sensor, however the CPS died shortly after pulling the QS off, so I'm reinstalling it.

TIA

Sent from my SM-G960F using Tapatalk

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome