Triumph675.Net Forums - Reply to Topic
General 675 discussion Anything related to the Triumph 675 model(s), and miscellaneous motorcycle talk.

Thread: Front brake lever replacement Reply to Thread
Title:
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now



In order to be able to post messages on the Triumph675.Net Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
11-24-17 21:09
Kevin7909 The oem plunger can be removed without damaging anything. Actually, it's a nifty design because it allows you to adjust the initial bite position of the brakes without modification or purchasing a brembo corsa costa. There is a very tiny hex set screw in the lever. If you loosen it the plunger will freely spin and you can either remove it or reposition it and retighten that hex set screw. It's not dimpled. If you adjust this plunger be very careful that you don't move it far enough to block the return hole in the mc.
10-27-17 20:34
Magnum Maximum
Quote:
Originally Posted by ramnakhle View Post
Quote:
Originally Posted by Magnum Maximum View Post
The problem is that the factory plunger cannot be removed from the stock levers, unless I destroy the stock levers to get it out (something that I do not want to do). The only other option is finding a place that has spare plungers laying around somewhere.


Been there done that.
It takes some wiggling but t will come out for sure. I remember it took me at least 45 min but it does come out.
Better than make-shifting it.
And no it will not come out of the aftermarket lever.


Sent from my iPhone using Tapatalk
Thanks for the advice. I was able to get it out. I was using the wrong tool. Had to find some plyers and was able to wiggle it out.
10-27-17 03:18
ramnakhle
Quote:
Originally Posted by Magnum Maximum View Post
The problem is that the factory plunger cannot be removed from the stock levers, unless I destroy the stock levers to get it out (something that I do not want to do). The only other option is finding a place that has spare plungers laying around somewhere.


Been there done that.
It takes some wiggling but t will come out for sure. I remember it took me at least 45 min but it does come out.
Better than make-shifting it.
And no it will not come out of the aftermarket lever.


Sent from my iPhone using Tapatalk
10-27-17 02:07
Magnum Maximum
Quote:
Originally Posted by MachOne View Post
I upgraded to Gilles Tooling levers and had the same issue. It looks like the plunger will unscrew from the Barrell, because it has a hex on it. So I put a deep socket on it, and cranked it loose. The threads immediately galled. The Gilles lever has a small dimple in it's barrel, so I slid the plunger under the boot like it's supposed to be, and set the Barrel dimple. The preload spring on the lever always keeps a small amount of pressure on it.

Sent from my Pixel XL using Tapatalk
I need the barrel too. The lever I bought didn't come with a barrel. That's the part that I'm having difficulty removing. I can't find anything that shows how to removed it.
10-26-17 21:32
MachOne I upgraded to Gilles Tooling levers and had the same issue. It looks like the plunger will unscrew from the Barrell, because it has a hex on it. So I put a deep socket on it, and cranked it loose. The threads immediately galled. The Gilles lever has a small dimple in it's barrel, so I slid the plunger under the boot like it's supposed to be, and set the Barrel dimple. The preload spring on the lever always keeps a small amount of pressure on it.

Sent from my Pixel XL using Tapatalk
10-26-17 20:44
Magnum Maximum
Quote:
Originally Posted by Renboy View Post
I just went to check, and your levers are virtually identical to mine and there is no way that the plunger will slide out of the lever. Drop the plunger into the lever, bolt the lever to the MC and try. It only takes 2 minutes to remove and replace the lever. I've had mine there for years and never once had a problem. You're creating more work for yourself than necessary.
The problem is that the factory plunger cannot be removed from the stock levers, unless I destroy the stock levers to get it out (something that I do not want to do). The only other option is finding a place that has spare plungers laying around somewhere.
10-26-17 13:06
Renboy I just went to check, and your levers are virtually identical to mine and there is no way that the plunger will slide out of the lever. Drop the plunger into the lever, bolt the lever to the MC and try. It only takes 2 minutes to remove and replace the lever. I've had mine there for years and never once had a problem. You're creating more work for yourself than necessary.
10-26-17 07:08
Magnum Maximum Ok, so I'm going with the route in making my own plunger. I'll be using a 3/8" shaft collar with a 1/4" spacer inserted in it. The shaft collar will have a set screw sticking out of it to make contact with the boot for the master cylinder. To keep the shaft collar and spacer secured in the lever, I'll be running a 10mm bolt that's 3/4" long through the spacer. This means I'll have to drill through the indentation on the lever where the plunger goes through. I'll secure the other end of the bolt with a washer and a 10mm nut. If this is a bad idea, please let me know now. If this is a great idea, I'll see if I can post pics of the process of building this part.
10-19-17 01:26
Magnum Maximum Here's the front brake lever that I bought. The plunger is supposed to fit in there. However, I don't feel to comfortable in just having it sit there and trust that it won't pop out. There's nothing covering that area when it's installed. I'm thinking of either returning it or make my own plunger that'll sit in there secured (which means drilling a hole in the base of that indent to have a nut securing it).
10-18-17 23:53
Renboy Assuming the same front master is used on newer Daytona R's as it was on the older (pre '13) R's, then the plunger is removable. Unfortunately I can't remember off hand how and it's too late to check (I'm in bed). I'll check tomorrow. The second thing to note, is that there is a difference in levers between the R's and non-R's, and they are NOT interchangeable. Are you sure you got the correct lever?
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome