Front end picture required.

Tricky · 12-01-12, 12:31

Hi

Long time lurker first time poster.
I fitted a set of GB racing covers to my 2012 Daytona today and removed both side fairings in the process. (Fantastic write up in the 'How to' section on how to do this by the way.
After refitting the fairing I've noticed a pipe and a cable running next to the horn/radiator and I am unsure of the routing for these.
Just in case I've made a mistake could someone please post a picture looking up at the horn/radiator from the front wheel if you have one.
Many thanks

Tricky

Tricky · 12-02-12, 06:18

Hi

Photo not needed now, I had a couple of cables from the RHS incorrectly routed.
Good practice by taking off the fairing again, only takes 5 minutes now.

Tricky

jardineD675 · 12-02-12, 16:01

O yah the bolts gb gives u I think are two long possibly, I remember getting maintenance done and they switched out bolts that where securing sliders. They had noticed a very small leak. Gb might of fixed this prob I got mine back in 2009. Just keep a look out.

Sent from my X10a using Motorcycle.com Free App

Tricky · 12-02-12, 16:56

Thanks for the heads up,
The bolts didn't bottom out and torqued up okay but ill keep an eye on them just in case.
I had a set on my Street Triple last year and they were quality.

Cheers

Tricky

jardineD675 · 12-04-12, 23:31

O yah read on a diff thread, make sure u put thread lock on them.

Sent from my X10a using Motorcycle.com Free App

Tricky · 12-05-12, 06:28

Hi
I'll do that, thanks
T

12-01-12, 12:31	#1
Tricky Junior Member Join Date: Dec 2012 Location: South Posts: 4	Front end picture required. Hi Long time lurker first time poster. I fitted a set of GB racing covers to my 2012 Daytona today and removed both side fairings in the process. (Fantastic write up in the 'How to' section on how to do this by the way. After refitting the fairing I've noticed a pipe and a cable running next to the horn/radiator and I am unsure of the routing for these. Just in case I've made a mistake could someone please post a picture looking up at the horn/radiator from the front wheel if you have one. Many thanks Tricky
Status: Offline

12-02-12, 06:18	#2
Tricky Junior Member Join Date: Dec 2012 Location: South Posts: 4	Hi Photo not needed now, I had a couple of cables from the RHS incorrectly routed. Good practice by taking off the fairing again, only takes 5 minutes now. Tricky
Status: Offline

12-02-12, 16:01	#3
jardineD675 Member Join Date: Dec 2012 Location: sacramento Posts: 206	O yah the bolts gb gives u I think are two long possibly, I remember getting maintenance done and they switched out bolts that where securing sliders. They had noticed a very small leak. Gb might of fixed this prob I got mine back in 2009. Just keep a look out. Sent from my X10a using Motorcycle.com Free App
Status: Offline

12-02-12, 16:56	#4
Tricky Junior Member Join Date: Dec 2012 Location: South Posts: 4	Thanks for the heads up, The bolts didn't bottom out and torqued up okay but ill keep an eye on them just in case. I had a set on my Street Triple last year and they were quality. Cheers Tricky
Status: Offline

12-04-12, 23:31	#5
jardineD675 Member Join Date: Dec 2012 Location: sacramento Posts: 206	O yah read on a diff thread, make sure u put thread lock on them. Sent from my X10a using Motorcycle.com Free App
Status: Offline

12-05-12, 06:28	#6
Tricky Junior Member Join Date: Dec 2012 Location: South Posts: 4	Hi I'll do that, thanks T
Status: Offline

Remove Advertisements Sponsored Links
Triumph675.net Advertisement

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode