2006 Graphite Side Fairings with R & G Crash Bungs/Mounting Hardware

Sammy901 · 11-21-12, 15:44

Left & right side fairings from a 2006 Graphite Daytona 675. Bike was sold in 2010 with trackday bodywork, these have not seen daylight since 2008. They have under 2000 street miles. I'd rate them a solid A in condition. Never down, all mounting tabs are intact. Please note that these have been modified (aka a hole cut in them) for R & G frame sliders that mount to the engine. I am including the frame sliders and the mounting hardware along with a pair of stock bar ends and hardware.

$300 Shipped Anywhere in the Continental USA. If you live in Florida or have someone who can pick them up I'll drop the price to $250. I live very close to Patrick Air Force Base/Cocoa Beach and am an hour east of Orlando.

Sam

Sammy901 · 11-23-12, 09:48

Hot.Damn. · 11-23-12, 21:05

Any interest in selling the frame sliders separate?

Sammy901 · 11-23-12, 22:48

Quote:

Originally Posted by Hot.Damn.

Any interest in selling the frame sliders separate?

I figure any chance of selling the fairings will be blown if I sell the frame sliders separately. People probably would not buy fairings with holes in them if they didn't have anything to fill the holes with.

If somebody posts up that they want the fairings without the sliders then you can contact them and work out how much each party would pay.

dlk7u · 11-26-12, 13:53

Hey-

Any chance you have the little r&g marking tool left over from your installation? I need to drill holes in my fairings for w/c sliders, and the r&g tool seems like a better solution than using a later pointer, etc

Thanks a lot,
Dan

Sammy901 · 11-26-12, 19:52

Quote:

Originally Posted by dlk7u

Hey-

Any chance you have the little r&g marking tool left over from your installation? I need to drill holes in my fairings for w/c sliders, and the r&g tool seems like a better solution than using a later pointer, etc

Thanks a lot,
Dan

I did see that thing a while ago somewhere in my tools or parts. I'll dig around for it and if I find it I'll let you know. You can have it for free if I can find it.

Sam

Sammy901 · 11-26-12, 20:03

Found it...Message me your address & I'll drop it in an envelope at work on Tuesday. Merry Xmas!!!

dlk7u · 11-27-12, 12:00

Amazing! Thanks!!!! I sent you a PM with my address and a question about how the tool works. I'll pass the tool along on the forum as soon as I'm done with it!

Cheers,
Dan

Sammy901 · 11-30-12, 10:31

Bump....Anyone? If nobody is interested I'll put them up on Fleabay.

Sam

Sammy901 · 12-06-12, 23:22

Any offers before Fleabay? I watch Pawn Stars so I know how to negotiate...

11-21-12, 15:44	#1
Sammy901 Senior Member Join Date: Jan 2006 Location: Near the Kennedy Space Center, FL Posts: 3,281	2006 Graphite Side Fairings with R & G Crash Bungs/Mounting Hardware Left & right side fairings from a 2006 Graphite Daytona 675. Bike was sold in 2010 with trackday bodywork, these have not seen daylight since 2008. They have under 2000 street miles. I'd rate them a solid A in condition. Never down, all mounting tabs are intact. Please note that these have been modified (aka a hole cut in them) for R & G frame sliders that mount to the engine. I am including the frame sliders and the mounting hardware along with a pair of stock bar ends and hardware. $300 Shipped Anywhere in the Continental USA. If you live in Florida or have someone who can pick them up I'll drop the price to $250. I live very close to Patrick Air Force Base/Cocoa Beach and am an hour east of Orlando. Sam Attached Thumbnails __________________ Eric Cartman : "my heart says yes, but my vah jay jay says no" Last edited by Sammy901; 11-23-12 at 09:46.
Status: Offline

11-23-12, 09:48	#2
Sammy901 Senior Member Join Date: Jan 2006 Location: Near the Kennedy Space Center, FL Posts: 3,281	__________________ Eric Cartman : "my heart says yes, but my vah jay jay says no"
Status: Offline

11-23-12, 21:05	#3
Hot.Damn. Junior Member Join Date: Oct 2012 Location: Wildomar Posts: 49	Any interest in selling the frame sliders separate? __________________ 2006 Daytona 675 Scorched Yellow 2008 Ninja 250R Ebony Black
Status: Offline

11-26-12, 13:53	#5
dlk7u Member Join Date: Mar 2012 Location: NYC Posts: 183	Marking tool Hey- Any chance you have the little r&g marking tool left over from your installation? I need to drill holes in my fairings for w/c sliders, and the r&g tool seems like a better solution than using a later pointer, etc Thanks a lot, Dan
Status: Offline

11-26-12, 20:03	#7
Sammy901 Senior Member Join Date: Jan 2006 Location: Near the Kennedy Space Center, FL Posts: 3,281	Found it...Message me your address & I'll drop it in an envelope at work on Tuesday. Merry Xmas!!! Attached Thumbnails __________________ Eric Cartman : "my heart says yes, but my vah jay jay says no"
Status: Offline

11-27-12, 12:00	#8
dlk7u Member Join Date: Mar 2012 Location: NYC Posts: 183	Amazing! Thanks!!!! I sent you a PM with my address and a question about how the tool works. I'll pass the tool along on the forum as soon as I'm done with it! Cheers, Dan
Status: Offline

11-30-12, 10:31	#9
Sammy901 Senior Member Join Date: Jan 2006 Location: Near the Kennedy Space Center, FL Posts: 3,281	Bump....Anyone? If nobody is interested I'll put them up on Fleabay. Sam __________________ Eric Cartman : "my heart says yes, but my vah jay jay says no"
Status: Offline

12-06-12, 23:22	#10
Sammy901 Senior Member Join Date: Jan 2006 Location: Near the Kennedy Space Center, FL Posts: 3,281	Any offers before Fleabay? I watch Pawn Stars so I know how to negotiate... __________________ Eric Cartman : "my heart says yes, but my vah jay jay says no"
Status: Offline

Remove Advertisements Sponsored Links
Triumph675.net Advertisement

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode